Making a Custom Serger Cover
I bought my Juki serger at the Original Sewing Expo last November, and I decided that I wanted to make a custom dust cover for the machine. I made the cover without a formal pattern, and I think it turned out pretty well.
Here is the following process I used to make my custom serger cover. Please note that sergers come in all different shapes and sizes and my dimensions are prior to trimming down to fit my specific serger. I also used a 1/2" seam allowance for all of my stitching.
Materials Needed:
- Approximately 1 yard of Outer Fabric
- Approximately 1 yard of Muslin
- Approximately 18"x 90" of batting
I figured my cover should have an overall quilted piece that covers front to back with two side pieces. In order to figure out the dimensions of the side pieces, the above diagram is how I measured my serger. Note: the measurements I came up with are ROUGH and rounded up. My thought was if it turns out too big, you could always trim it down during construction.
I did not actually measure the diagonal, I figured I could cut the diagonal when I trimmed the side pieces. I sketched out the side pieces on my graph paper and added 1" to each of the dimensions to account for a 1/2" seam allowance I planned on using. I did a little math to add up the edges and the total was just over 44". I decided that I would not add any length to the width of fabric panel that I created because I was oversizing anyway.
The next step is to quilt the panels. I cut my panels to quilt slightly larger so I had space to trim it down after quilting. My quilting was a straight line quilting on the short sides approximately 1.5" apart. I set aside the piece I made that was width of fabric.
For the quilted panels, remember that these are mirrored. I folded the quilted panel in half with the right sides of the fabric facing outwards to cut mirror image pieces of the side panels. Once I have these cut to my rough dimensions, I physically put it next to my serger to fine tune my sizing. I ended up taking off about 1.5" from the bottom and 0.5" from the top.
With right sides together, sew one panel to the width of fabric panel that covers the serger from front to back. Take the cover back to the serger and trim the width to the desired fit of the cover. Now, sew the other panel to the cover. The last step is to put the cover over your machine and trim the length to the desired fit. Ta Da!
I was thinking that I should add some binding to the edge and maybe add lining to the cover, but the obvious answer came to me… I can serger the ends!!!! I sergered the inside seams and the outer edge of the cover to finish it off!
Have you ever made custom items without a pattern? How did it turn out for you?
Join me again on Friday for Friday Foto Fun and on Sunday for the #365DayOfArtPBQChallenge! Link up and share your progress on your own projects!
Need more fabric, tools or notions? Shop my affiliate links:
Amazon - Shop now!
Fat Quarter Shop - Shop now!
Fabric.com - Shop now!
Craftsy - Shop now!
Congratulations on your awesome new machine! The cover is adorable. I’ve made a custom sewing machine cover for my machine based on my measurements since it recedes into a flatbed table, although mine isn’t as complicated as yours. I just had a flat quilted piece with ties on each side.
Thanks Liz! I don’t actually use my serger a ton… hence why I almost forgot I could serger my ends on the cover! I had thought about doing ties on the sides as well, but with the goofy shape of the serger I figured, I might as well try to make a fitting one. 🙂 See you soon!!!
I’ve been contemplating making a cover for my machine, and designing my own since I don’t really like the patterns I’m finding online. I have the charm pack, ready and waiting. It’s on my project list, just waiting for the right “squirrel” moment! Your serger cover turned out really well, and I like the fabric! BTW — have you gotten your baby back yet??
Good luck designing a cover! I was a little apprehensive about doing patchwork cover so I opted for a single fabric. I actually picked up my machine when you were out in WI! We do need to plan a trip to Quilt Cove! I should be home the next couple weekends… except for Quiltcon at the end of the month!
I love winging it with a plan and you did it. Can’t remember the last thing like that I did but I think it was a cover for my husband’s keyboard!
A keyboard cover, how cool! I am always a bit apprehensive about winging it, but I’m always surprised with how well stuff turns out! I made a bag for my surface like 2 years ago that I look at now and think how did I even make this thing?! I don’t know if I could duplicate it. I should have taken better notes!